Category: question bank

ME8651 Question Bank Design of Transmission Systems

ME8651 Question Bank Design of Transmission Systems Regulation 2017 Anna University free download. Design of Transmission Systems Question Bank ME8651 pdf free download.

Sample ME8651 Question Bank Design of Transmission Systems

A truck equipped with 9.5 KW engine uses a roller chain of the final drive to the rear axle. The driving sprocket runs at 900 rpm and driven sprocket at 400 rpm with a center distance
of approximately 600 mm. select a suitable the roller chain.
ME8651 Question Bank Design of Transmission Systems
A roller chain drive is used between a driver shaft running at 1440rpm and a driven shaft running approximately at 720rpm. The power transmitted is 15KW. The drive is to be used for 2 shifts/day with 8hours/shift. The center distance is approximately 1000mm and the chain tension can be adjusted by moving the motor in the rails. Design the drive.
ME8651 Question Bank Design of Transmission Systems
A work shop crank carries a load of 30KN using wire ropes and a hook. The hook weighs 15KN. Diameter of the rope drum is 30 times the diameter of the rope. The load is lifted with an acceralation of ME8651 Question Bank Design of Transmission Systems

A compressor is to run by a motor pulley running at 1440 rpm, speed ratio 2.5.

A centrifugal pump running at 340rpmisto be driven by a 100kw motor running at 1440rpm. The drive is to work for at least 20 hours every day. The centre distance between the motor shaft and the pump shaft is 2000mm. Suggest a suitable multiple V-belt drive for this application. Also calculate the actual belt tensions and stress induced.

Subject name	Design of Transmission Systems
Short Name	DTS
Semester	6
Subject Code	ME8651
Regulation	2017 regulation

ME8651 Question Bank Design of Transmission Systems Click Here To Download 

 ME8651 Design of Transmission Systems Syllabus

---

ME8651 Design of Transmission Systems Notes

---

ME8651 Design of Transmission Systems Important Questions

---

ME8651 Design of Transmission Systems Question Paper

CE8005 Question Bank Air Pollution and Control Engineering

CE8005 Question Bank Air Pollution and Control Engineering Regulation 2017 Anna University free download. Air Pollution and Control Engineering Question Bank CE8005 pdf free download.

Sample CE8005 Important Questions Urban Planning and Development

1.
Explain how do you control the emission of NOx by the following treatment methods:
(a) Absorption by H2SO4.
(b) Absorption by Magnesium Hydroxide
(c) Adsorption by Solids.
BT 4
Analyzing
2.
(i) Write the general principle involved in absorption.
(ii) Explain the criteria to achieve high performance in gas absorption equipments.
CE8005 Question Bank Air Pollution and Control Engineering
Discuss the sources of pollutants and its control in a cement industry.
BT 1
Remembering
4.
Explain briefly about the methods of biological air treatment system.
BT 1
Remembering
5.
(i) Discuss on absorption method of control of gaseous contaminants.
(ii) Write a brief note on engineering design of condensation mode of air pollution control.
CE8005 Question Bank Air Pollution and Control Engineering
Briefly discuss on types of carbon adsorption system with suitable neat sketch.
BT 2
Understanding
7.
Tabulate the National air quality standards for residential, Industrial and sensitive areas.

8.
Define adsorption and differentiate between physical and chemical adsorption.
BT 3
Applying
9.
Write the list of industries specified in the schedule under Air Act 1981.
BT 4
Analyzing
10.
How London smog is different from Los Angeles Smog? Explain.
CE8005 Question Bank Air Pollution and Control Engineering
Write a short note about condensation process with examples.
CE8005 Question Bank Air Pollution and Control Engineering
Write a short note about Incineration process with sketches.

Subject name	Air Pollution and Control Engineering
Short Name	APDE
Semester	6
Subject Code	CE8005
Regulation	2017 regulation

CE8005 Question Bank Air Pollution and Control Engineering Click Here To Download

CE8005 Air Pollution and Control Engineering Syllabus

---

CE8005 Air Pollution and Control Engineering Notes

---

CE8005 Air Pollution and Control Engineering Important Questions

---

CE8005 Air Pollution and Control Engineering Question Paper

CE8004 Question Bank Urban Planning and Development

CE8004 Question Bank Urban Planning and Development Regulation 2017 Anna University free download. Urban Planning and Development Question Bank CE8004 pdf free download.

Sample CE8004 Question Bank Urban Planning and Development

1.
Give the checklist for a site analysis.
BT1
Remembering
2.
Mention the significance of site analysis for urban planning.
BT1
Remembering
3.
Define a layout design.
CE8004 Question Bank Urban Planning and Development
List the urban planning standards.
BT1
Remembering
5.
State urban planning formulation.
BT1
Remembering
6.
Mention the purpose of planning standards.
CE8004 Question Bank Urban Planning and Development
What are the planning standards of recreational areas?
BT2
Understanding
8.
Define project formulation.
BT2
Understanding
9.
List the steps of project formulation.
CE8004 Question Bank Urban Planning and Development
Mention the objectives of project formulation.
BT2
Understanding
11.
How does project formulation enhance the effectiveness of urban development?
BT3
Applying
12.
List the factors to be considered for the evaluation of urban development project.
BT3
Applying
13.
Mention the significance of project evaluation.
CE8004 QB Urban Planning and Development
Define plan implementation.
BT4
Analyzing
15.
What is principle of plan implementation?
BT4
Analyzing
16.
List the constraints of implementing the urban development project.
BT4
Analyzing
17.
How can we overcome the constraints in the execution of development project?
BT5
Evaluating
18.
List the types of financing methods for urban development.
BT5
Evaluating
19.
Define value recycling financing.
BT6
Creating
20.
What is value realization?

7.
Give a detail study on the development project formulation and its implementation.
BT2
Understanding
8.
Discuss in detail about the purpose and risks of project formulation for urban development.
BT3
Applying
9.
Explain the details about the considerations for the evaluation of urban development project.

Subject name	Urban Planning and Development
Short Name	UPD
Semester	6
Subject Code	CE8004
Regulation	2017 regulation

CE8004 Question Bank Urban Planning and Development Click Here To Download

CE8004 Urban Planning and Development Syllabus

---

CE8004 Urban Planning and Development Notes

---

CE8004 Urban Planning and Development Important Questions

---

CE8004 Urban Planning and Development Question Paper

EN8592 Question Bank Wastewater Engineering

EN8592 Question Bank Wastewater Engineering Regulation 2017 Anna University free download. Wastewater Engineering Question Bank EN8592 pdf free download.

Sample EN8592 Question Bank Wastewater Engineering

9.
How will you compute peak storm water discharge by the use of empirical formulas?
BT-3
Application
10.
i) Explain the terms BOD and COD. Differentiate between first and second stage BOD. (6)
ii) The BOD of a sewage incubated for one day at 30oc has been found to be 120mg/l. Identify the 5-day BOD at 20oC. Assume BOD rate constant K = 0.21 (base e) per day at 20oc and temperature correction coefficient
EN8592 Question Bank Wastewater Engineering
i) Discuss the choice available and the factors to be considered while selecting pumps and pipes for sewerage system and explain. (6)
ii) With help of neat sketch explain the location and functions of drop manhole ‘inverted siphon’. (7)
BT-4
Analyse
12.
i) Explain the factors influencing sanitary sewage flow and its estimation. (6)
ii) State the classification of solids present in sewage and the removal methods of each. (7)
EN8592 Question Bank Wastewater Engineering
i) Generalize how will you estimate the relative stability of sewage? (6)
ii) Compose the different sources of waste water that are produced from a community. Discuss the systems of sewerage with its merits and demerits.

3.
Explain the various physio-chemical characteristics of sewage and state their environmental significance.
EN8592 QB Wastewater Engineering

Design a sanitary sewer to a population of 6000 receiving water at rate of 90 lpcd. Minimum self-cleansing velocity at design flow is 0.8m/s. Maximum depth of flow is 0.5D. Assume other design criteria as applicable.

Subject name	Wastewater Engineering
Short Name	WE
Semester	6
Subject Code	EN8592
Regulation	2017 regulation

EN8592 Question Bank Wastewater Engineering Click Here To Download

 EN8592 Wastewater Engineering Syllabus

---

EN8592 Wastewater Engineering Notes

---

EN8592 Wastewater Engineering Important Questions

---

EN8592 Wastewater Engineering Question Paper

CE8604 Question Bank Highway Engineering

CE8604 Question Bank Highway Engineering Regulation 2017 Anna University free download. Highway Engineering Question Bank CE8604 pdf free download.

Sample CE8604 Question Bank Highway Engineering

3.
i. What are transition curves? How will you determine the length of transition curves? (8)
ii. A National Highway passing through rolling terrain of heavy rainfall area, R=500m. Assume suitable data and design the length of Transition curve. (8)
CE8604 Highway Engineering  Question Bank
Calculate the safe stopping sight distance for the design speed of 50 kmph. Assume co-efficient of friction as 0.37 and reaction time of driver as 2.5 seconds.
i) Two way traffic on a two lane road and
ii) Two way traffic on a single lane road.
BT -2
Understand
5.
Explain and derive the equation for sight distances.
CE8604 Highway Engineering  Question Bank
i. Explain PIEV theory (7)
ii. Discuss the methods of attaining super elevation. (6)
BT -2
Understand
7.
Calculate the minimum sight distance required to avoid a head on collision of two cars approaching from the opposite direction at 90 and 60 kmph. Assume a reaction time of 2.5 seconds coefficient of friction of 0.7 and brake efficiency of 50 % in either case.
CE8604 Highway Engineering  Question Bank
The speed of overtaking and over taken vehicles are70 and 40 kmph, respectively on a two-way traffic road. If the acceleration of overtaking vehicle is 0.99m/s2. Calculate SSD, OSD and ISD
BT- 3
Apply
9.
Calculate the safe sight distance for the design speed of 60 kmph for
a. Two-way traffic on a two-lane road (3)
b. Two- way traffic on a single lane road (3)
c. Two-way traffic on a two-lane road with an ascending gradient of 2% (3)
d. Two- way traffic on a two-lane road with an descending gradient of 3% (4)
CE8604 Highway Engineering

Subject name	Highway Engineering
Short Name	HE
Semester	6
Subject Code	CE8604
Regulation	2017 regulation

CE8604 Question Bank Highway Engineering Click Here To Download 

CE8604 Highway Engineering Syllabus

---

CE8604 Highway Engineering Notes

---

CE8604 Highway Engineering Important Questions

---

CE8604 Highway Engineering  Question Paper

CE8603 Question Bank Irrigation Engineering

CE8603 Question Bank Irrigation Engineering Regulation 2017 Anna University free download. Irrigation Engineering Question Bank CE8603 pdf free download.

Sample CE8603 Question Bank Irrigation Engineering

1.
Write in detail about the component parts of diversion works.
BT-1
Remember
2.
What are the types of weirs and Explain various components of weir?
CE8603 Question Bank Irrigation Engineering
Write in detail about the tank surplus works.
BT-1
Remember
4.
What are the causes of failure of Earth dam, Gravity dam and Earth dam? State its remedies.
BT-1
Remember
5.
Explain the factors affecting the selection of type of a dam.
BT-2
Understand
6.
Give an outline on the causes of Failure in weir on permeable foundation and how to overcome it?
CE8603 Question Bank Irrigation Engineering
Summarize the criteria for safe design of earth dam.
BT-2
Understand
8.
Identify the forces acting on a gravity dam.
BT-3
Application
9.
Identify the forces acting on an earth dam.
BT-3
Application
10.
Classify types of dams and list the comparative merits and demerits of various types of dams.
BT-4
Analyse
11.
Categorize the various types of spillways and types of gates used in spillways.
CE8603 QB Irrigation Engineering
Analyze in detail about Percolation pond and factors to be considered for a percolation pond.

List the uses of dams.
BT-4
Analyze
17.
Determine the different types of diversion head works.
BT-5
Evaluate
18.
Compare weir and dam (barrage).
BT-5
Evaluate
19.
Discuss how a spillway differs from a sluice?
BT-6
Create
20.
Estimate the failures that occur during the construction of earth dam.
BT-6
Create
21.
Define Percolation pond?
BT-1
Remember
22.
Illustrate the functions of scouring sluices.
BT-2
Understand
23.
Identify the component parts of diversion headwork.
BT-3
Application
24.
Categorize the purposes of diversion headwork.
CE8603 QB Irrigation Engineering
Explain diversion headwork.

Subject name	Irrigation Engineering
Short Name	IE
Semester	6
Subject Code	CE8603
Regulation	2017 regulation

CE8603 Question Bank Irrigation Engineering Click Here To Download

CE8603 Irrigation Engineering Syllabus

---

CE8603 Irrigation Engineering Notes

---

CE8603 Irrigation Engineering important questions

---

CE8603 Irrigation Engineering Question Paper

CE8602 Question Bank Structural Analysis 2

CE8602 Question Bank Structural Analysis 2 Regulation 2017 Anna University free download. Structural Analysis 2 Question Bank CE8602 pdf free download.

Sample CE8602 Question Bank Structural Analysis 2

1.
A circular three hinged arch of span 25m with a central rise of 5m is hinged at the crown and the end supports. It carries a point load of 100kN at 6m from the left support. Examine and Calculate the reaction at the supports and Moment at 5m from the left support.
CE8602 Question Bank Structural Analysis 2

A three hinged circular arch of span 16m and rise 4m is subjected to two point loads of 100 kN and 80 kN at the left and right quarter span points respectively. Examine and find the reaction at the supports. Find also the bending moment, radial shear and normal thrust at 6m from left support.
CE8602 Question Bank Structural Analysis 2

A symmetrical three hinged arch has a span of 50 & rise 5m. Find and examine the maximum bending moment at a quarter point of the arch caused by a uniformly distributed load of 10kN/m which occupies any portion of the span. Indicate the position of the load for this condition.
CE8602 Question Bank Structural Analysis 2

Describe cable structures. Mention its needs
BT1
Remember
2
Examine the true shape of cable structures.

A Parabolic three hinged arch carries loads as shown in figure. Determine the resultant reactions at support. Find the BM, Normal Thrust and radial shear at D, 5m from A, what is the maximum BM?

Formulate the expression for horizontal thrust in a two hinged semi-circular arch of radius R, carrying a point load W at the crown.

Subject name	Structural Analysis 2
Short Name	SA 2
Semester	6
Subject Code	CE8602
Regulation	2017 regulation

CE8602 Question Bank Structural Analysis 2 Click Here To Download 

CE8602 Structural Analysis 2 Syllabus

---

CE8602 Structural Analysis 2 Notes

---

CE8602 Structural Analysis 2 Important Questions

---

CE8602 Structural Analysis 2 Question Paper

CE8601 Question Bank Design of Steel Structural Elements

CE8601 Question Bank Design of Steel Structural Elements Regulation 2017 Anna University free download. Design of Steel Structural Elements Question Bank CE8601 pdf free download.

Sample CE8601 Question Bank Design of Steel Structural Elements

4.
Design a single angle to carry a tension of 100 kN. The fillet weld is to be used. fu = 410 MPa and fy= 250MPa.
CE8601 Question Bank Design of Steel Structural Elements
Design a tension member of length 3.6 m to carry a pull of 150 kN. The member is subjected to a reversal of stresses.
CE8601 Question Bank Design of Steel Structural Elements
Determine the design tensile strength of the plate 130 x 12 mm with the holes for 4 nos. of 16 mm diameter bolts arranged two in a row. Steel used is of Fe 410 grade quality. Pitch = 60 mm and edge distance = 35 mm.
BT-3
Apply
7.
Design a single angle to carry a tension of 100 kN. The end connection is to be done using M20 bolts of 4.6 grade. The yield and ultimate strength of steel used are 250 MPa and 410 MPa respectively.
CE8601 Question Bank Design of Steel Structural Elements
Write the procedure for the design of tension members.
BT-6
Create
9.
Design a 10 m long tension member subjected to a factored tensile load of 2000 kN. The section should consist of 2 channels facing each other. The rolled channels ISMC 300 at 358 N/m only are available. Assuming the channels to be weakened by one bolt hole only, check the adequacy of the section. Use Fe 410 grade of steel. The bolts to be used are of grade 4.6 and of 16 mm diameter.
BT-4
Analyse
10.
Determine the tensile strength of a roof truss member 2 ISA
90x60x6 mm connected to the gusset plate of 8 mm thickness by 4mm weld. The effective length of weld is 200mm.
CE8601 Question Bank Design of Steel Structural Elements

Subject name	Design of Steel Structural Elements
Short Name	DSSE
Semester	6
Subject Code	CE8601
Regulation	2017 regulation

CE8601 Question Bank Design of Steel Structural Elements Click Here To Download 

CE8601 Design of Steel Structural Elements Syllabus

---

CE8601 Design of Steel Structural Elements Notes

---

CE8601 Design of Steel Structural Elements Important Questions

---

CE8601 Design of Steel Structural Elements Question Paper

EE8006 Question Bank Power Quality

EE8006 Question Bank Power Quality Regulation 2017 Anna University free download. Power Quality Question Bank EE8006 pdf free download.

Sample EE8006 Question Bank Power Quality

1. Explain the methods to evaluate harmonic distortion and devices
to control. (13)
4 Analyze CO 3
2. (i)Explain the IEEE and IEC standards on harmonics distortion.
(7)
(ii)What are the filters in harmonic analysis? Explain active and
passive filters (6)
EE8006 Question Bank Power Quality
3. (i) Explain briefly how the phenomena of current distortion
affects the voltage distortion under the presence of harmonics
(7)
(ii) Explain briefly about locating harmonic sources and
characterization in power system (6)
4
4
EE8006 Question Bank Power Quality
4. (i) Explain the power system response characteristics under the
presence of harmonics. (7)
(ii)What is the need of IEEE standards used in harmonics
studies? Give their philosophy and objectives of these standards
(6)
4
1
Analyze
Remember
CO 3
CO 3
5. Explain briefly about the sources of harmonics generation and
waveform distortion. (13)
4 Analyze CO 3
6. Discuss the effects of harmonics on electrical power components
(13)
2 Understand CO 3
7. Write short note on the active filter and passive filter in
controlling harmonic distortion (13)
1 Remember CO 3
8. Explain how commercial and industrial loads are responsible for
harmonic distortion. (13)
EE8006 Question Bank Power Quality
9. Determine the RMS and THD of the following waveform

1. What are the devices used for controlling harmonic distortion and
explain their function (15) 5 Evaluate
CO 3
2. Explain briefly about harmonic distortion and conduct an
evaluation of study (15)
4
Analyze CO 3
3. Explain briefly about the phenomena of how current distortion
affects the voltage distortion under the presence of harmonics

4. Explain the function of active filters and how it overcomes the
drawbacks of passive filter in controlling harmonic

Subject name	Power Quality
Short Name	PQ
Semester	6
Subject Code	EE8006
Regulation	2017 regulation

EE8006 Question Bank Power Quality Click Here To Download

EE8006 Power Quality Notes

---

EE8006 Power Quality Syllabus

---

EE8006 Power Quality Important Questions

---

EE8006 Power Quality Question Paper

EE8005 Question Bank Special Electrical Machines

EE8005 Question Bank Special Electrical Machines Regulation 2017 Anna University free download. Special Electrical Machines Question Bank EE8005 pdf free download.

Sample EE8005 Question Bank Special Electrical Machines

1 State the principle of operation of switched
reluctance motor.
BTL 1 Remember CO3
2 List out the advantages of switched reluctance
motors.
BTL 1 Remember CO3
3 Illustrate the different modes of operation of
switched reluctance motor.
BTL 3 Apply CO3
4 Differentiate switched reluctance motor
and variable reluctance stepper motor.
BTL 5 Evaluate CO3
5 Give basic features or characteristics of
Switched Reluctance motor
BTL 2 Understand CO3
6 What are the disadvantages of a switched
reluctance motor?
BTL 2 Understand CO3
7 Give the expression for torque of a switched
reluctance motor
EE8005 Question Bank Special Electrical Machines
8 Write the relations between the speed and
fundamental switching frequency
BTL 1 Remember CO3
9 Determine the step angle of a three phase
switched reluctance motor having 12stator
poles and 8 rotor poles. What is the
commutation frequency in each phase of
6000rpm?
BTL 4 Analyze CO3
10 Evaluate the speed-torque characteristics of
SRM.
BTL 5 Evaluate CO3
11 List out the basic requirements of power
semiconductor switching circuits employed for
switched reluctance motor.
EE8005 Question Bank Special Electrical Machines
12 Point out the different power controllers used
for the control of switched reluctance motor

13 What are the merits of classic converter or
power controller in SRM?
BTL 2 Understand CO1
14 What are the merits of Dump C – Converter? BTL 1 Remember CO1
15 Illustrate why SR machines popular in
adjustable speed drives.
EE8005 Question Bank Special Electrical Machines
16 List out the advantages and disadvantages of
the converter circuit with two power
semiconductor devices and two diodes per
phase?
BTL 1 Remember CO1
17 What is the significance of closed loop control
in switched reluctance motor?
BTL1 Remember CO1
18 What are the two types of current control
techniques?
EE8005 Question Bank Special Electrical Machines
19 Give the advantages of sensorless operation of
switched reluctance motor.
BTL 4 Analyze CO3
20 Illustrate the applications of switched
reluctance motor.

Subject name	Special Electrical Machines
Short Name	SEM
Semester	6
Subject Code	EE8005
Regulation	2017 regulation

EE8005 Question Bank Special Electrical Machines Click Here To Download

 EE8005 Special Electrical Machines Notes

---

EE8005 Special Electrical Machines Syllabus

---

EE8005 Special Electrical Machines Important Questions

---

EE8005 Special Electrical Machines Question Paper